João Murta Pina

An equivalent model and electromechanical characteristics for the disk motor was obtained based on the Steinmetz parameters. This paper describes a series of tests conducted on an axial flux motor, equipped with an aluminum rotor disc and an YBCO high temperature superconducting rotor disc, at liquid nitrogen temperature (77 K). The rotating magnetic field was produced by a four-pole, three-phase stator winding, at 50 Hz. At asynchronous permanent regime, Steinmetz-type models are able to describe both motors' behavior. From the performed tests, the parameters of both motors' models were deduced. A variable load was used to obtain both motor's characteristics (conventional and superconducting). Experimental obtained characteristics of both motors are compared with the ones predicted from parameters' calculation. The HTS motor provides high efficiency then the conventional ones.

An equivalent model and electromechanical characteristics for the disk motor was obtained based on the Steinmetz parameters. This paper describes a series of tests conducted on an axial flux motor, equipped with an aluminum rotor disc and an YBCO high temperature superconducting rotor disc, at liquid nitrogen temperature (77 K). The rotating magnetic field was produced by a four-pole, three-phase stator winding, at 50 Hz. At asynchronous permanent regime, Steinmetz-type models are able to describe both motors' behavior. From the performed tests, the parameters of both motors' models were deduced. A variable load was used to obtain both motor's characteristics (conventional and superconducting). Experimental obtained characteristics of both motors are compared with the ones predicted from parameters' calculation. The HTS motor provides high efficiency then the conventional ones.

A presente dissertação surge pelo interesse em estudar a adequação do uso de sistemas solares fotovoltaicos na electrificação de serviços primários em povoados remotos nos países Africanos mais carenciados. A abordagem teórica tem como objectivo principal reflectir sobre a importância destas aplicações intervindo naquelas que são consideradas as maiores dificuldades dos países subdesenvolvidos, ou seja, saneamento básico, serviços de saúde e meios de comunicação adequados. Nesse contexto estuda-se a viabilidade de alimentar com energia eléctrica produzida localmente unidades sanitárias na província de Sofala (Moçambique). O trabalho exigiu por isso um estudo de caso baseado numa dessas unidades. Mediante a análise das amostras recolhidas para esta investigação elaborou-se através de ferramentas informáticas um dimensionamento e uma modelação adequadas ao sistema fotovoltaico a ser implementado. Os resultados obtidos de acordo com os requisitos da unidade sanitária permitiram dimensionar os elementos do sistema bem como, simular hora a hora o seu funcionamento diário ao longo do ano. Uma vez provada a sua viabilidade incluiuse ainda neste trabalho um anteprojecto da instalação.

In this paper, a poly-phase disc motor innovative feeding and control strategy, based on a variable poles approach, and its application to a HTS disc motor, are presented. The stator windings may be electronically commutated to implement a 2, 4, 6 or 8 poles winding, thus changing the motor's torque?speed characteristics. The motor may be a conventional induction motor with a conductive disc rotor, or a new HTS disc motor, with conventional copper windings at its two iron semi-stators, and a HTS disc as a rotor. The conventional induction motor's operation principle is related with the induced electromotive forces in the conductive rotor. Its behaviour, characteristics (namely their torque?speed characteristics for different number of pole pairs) and modelling through Steinmetz and others theories are well known. The operation principle of the motor with HTS rotor, however, is rather different and is related with vortices' dynamics and pinning characteristics; this is a much more complex process than induction, and its modelling is quite complicated. In this paper, the operation was simulated through finite-elements commercial software, whereas superconductivity was simulated by the E-J power law. The Electromechanical performances of both motors where computed and are presented and compared. Considerations about the systems overall efficiency, including cryogenics, are also discussed.

In this paper, a poly-phase disc motor innovative feeding and control strategy, based on a variable poles approach, and its application to a HTS disc motor, are presented. The stator windings may be electronically commutated to implement a 2, 4, 6 or 8 poles winding, thus changing the motor's torque?speed characteristics. The motor may be a conventional induction motor with a conductive disc rotor, or a new HTS disc motor, with conventional copper windings at its two iron semi-stators, and a HTS disc as a rotor. The conventional induction motor's operation principle is related with the induced electromotive forces in the conductive rotor. Its behaviour, characteristics (namely their torque?speed characteristics for different number of pole pairs) and modelling through Steinmetz and others theories are well known. The operation principle of the motor with HTS rotor, however, is rather different and is related with vortices' dynamics and pinning characteristics; this is a much more complex process than induction, and its modelling is quite complicated. In this paper, the operation was simulated through finite-elements commercial software, whereas superconductivity was simulated by the E-J power law. The Electromechanical performances of both motors where computed and are presented and compared. Considerations about the systems overall efficiency, including cryogenics, are also discussed.

In this paper, a poly-phase disc motor innovative feeding and control strategy, based on a variable poles approach, and its application to a high temperature superconductor (HTS) disc motor, are presented. The stator windings may be electronically commutated to implement a 2, 4, 6 or 8 poles winding, thus changing the motor's torque?speed characteristics. The motor may be a conventional induction motor with a conductive disc rotor, or a new HTS disc motor, with conventional copper windings at its two iron semi-stators and a HTS disc as a rotor. The conventional induction motor's operation principle is related with the induced electromotive forces in the conductive rotor. Its behaviour, characteristics and modelling through Steinmetz and others theories are well known. The operation principle of the motor with HTS rotor, however, is rather different and is related with vortices' dynamics and pinning characteristics; this is a much more complex process than induction, and its modelling is quite complicated. In this paper, the operation was simulated through finite-elements commercial software (FLUX2D), whereas superconductivity was simulated by the E-J power law. The electromechanical performance of both motor's computed are compared. Considerations about the systems overall efficiency, including cryogenics, are also discussed.

A instalação em larga escala de turbinas eólicas equipadas com um gerador de indução duplamente alimentado (GIDA) tem vindo a promover a realização de vários estudos relacionados com potenciais soluções para a sua integração na rede eléctrica. Nesta tese apresenta-se uma técnica de controlo que permite regular as potências activa e reactiva do GIDA de forma estável e independente. A sua viabilidade é suportada não só por um estudo teórico prévio mas também pelos resultados da simulação de modelos desenvolvidos usando o software Matlab?Simulink?. Apesar de este sistema funcionar a velocidade variável (ainda que dentro de certos limites), continua a existir a necessidade de limitar a potência fornecida pela turbina eólica quando a velocidade do vento assume valores superiores ao nominal. Assim, faz-se também uma breve análise de alguns métodos de regulação de potência activos e passivos.

Os motores de histerese são muito atraentes, numa ampla gama de aplicações devido à característica binário - velocidade e simplicidade de construção. É esperado que o rendimento destes motores seja melhorado aquando do uso de materiais supercondutores de alta temperatura (SAT ? supercondutores de alta temperatura) e, de facto, os motores de histerese têm-se mostrado como, provavelmente, a melhor máquina eléctrica usando materiais SAT. Ambos os motores, quer convencional quer supercondutor (com SAT), são motores de histerese, mas apresentam diferentes fenómenos físicos para o seu funcionamento: o comportamento de histerese nos materiais ferromagnéticos convencionais é devido à falta de linearidade das suas propriedades magnéticas dos materiais ferromagnéticos enquanto a histerese nos materiais supercondutores de alta temperatura é de natureza ohmica e está relacionada com dinâmica de vórtices. Nesta tese aspectos teóricos, experimentais e simulados de ambos os motores são discutidos, realçando-se o princípio de funcionamento de cada um e as características mais relevantes de cada um. As características obtidas, quer por testes experimentais quer por uso do simulador usando elementos finitos (FLUX2D?), foram comparadas com o objectivo de avaliar o rendimento dos motores electromecânicos e a eficiência dos sistemas, incluindo a criogenia para os dispositivos supercondutores de alta temperatura.

The electric and magnetic properties of high temperature superconductors and the possibility to cool them by cheap liquid nitrogen makes them attractive in power applications. An all superconducting linear synchronous motor is presented in this paper in order to quantify the benefits and disadvantages of such applications. The term ?all superconducting? is related with the absence of copper conductors and iron parts. Certain characteristics of the superconducting materials impose severe restrictions when used, e.g., as armature windings. A numerical method for deriving the thrust and lift forces developed in such a motor, driven by a typical current inverter, is presented.

Magnetic shielding inductive fault currentlimiterswith high temperature superconducting cylinders have previously been described by a characteristic (or maximum)hysteresisloop, built from properties of their constitutive parts, which allowed predicting their behavior in electrical grids. These preliminary results were based on finite elements simulations, but posterior experiments suggested limitations in the models. In order to investigate the application of these previous models to real devices, two laboratory scale prototypes were built with different types of superconducting material in the secondary, either bulk cylinder, either tape. Although the behavior of both devices is still approximately defined by a maximumhysteresisloop, differences in the shielding current response, when compared with previous model, must be incorporated in future models.